In short, the MLX is adjustable to a wide range of UTVs, installs and uninstalls in under one minute, does not bolt on to any part of the UTV's frame, and does not reduce your UTV’s ground clearance.

The MLX is rated for a maximum load capacity of 350 pounds. Even if your winch is able to pull more weight, the Mod Lift X and its implements are rated and tested for up to 350lbs only. How much can the pallet forks lift? The forklifts are rated for 350 lbs total weight. What tongue weight can the ball mount/receiver handle? We rate the ball mount attachment for 350 lbs of tongue weight. A rough estimate of your trailer’s tongue weight is 10% of the trailer’s total weight, but refer to your trailer’s manufacturer or owner’s manual if you’re not sure. How much weight can the cargo carrier hold? The cargo carrier is rated for 350 lbs total weight.

Your purchase of the Mod Lift X comes with a pair of 30” pallet forks, and a ball mount/receiver. You will need to supply your own trailer ball. The ball mount accepts a ball with a 1” or less shaft diameter (typically, 1 7/8”, 2”, or 2 5/16”). Head over to our Shop page to see other MLX implements and accessories. We will be releasing more implements in the future (some in the very near future!). Make sure to follow our socials and subscribe to our newsletter to hear about new releases.

We’re actively looking for new authorized dealers and will be growing the MLX family in the near future. You can check out our current authorized dealers on the Find a Dealer page. Make sure to follow our socials or subscribe to our newsletter to be notified as we add new dealers (and release new implements/accessories)!

Not necessarily. However, just like using a snow plow on your UTV, the added weight to the front will cause for front shocks to compress more the heavier the load. If you like, you can reduce the compression by inserting coil spring spacers like the ones shown below. These are a $25 extra that are specifically made for using the snowplow on a UTV, and can be purchased HERE.

For safety purposes, we recommend a maximum speed of ten miles per hour while transporting a payload or moving a trailer. Also, always use the safety pins and secure your payload with rope, bungee cords, or other tie down mechanism. When the MLX is installed but not carrying any payload (or moving a trailer), there are no speed limitations if it is in the upright position, secured with safety pins, and the forks are properly stowed.

You secure loads with your preferred tie down mechanism, e.g., bungee cords or rope.

The Mod Lift X is constructed from powder-coated steel. Without a doubt, powder coating is tough (much tougher than regular paint), but we intend for you to be rough with the MLX, and over time the powder coat may chip. When that happens and the steel is exposed to moisture, it will show rust but that will not impact the integrity or functionality of your MLX. If you want to keep your MLX looking new, we suggest using a powder coat touch-up pen, which you can find online. As for being waterproof, the MLX itself is fully submersible, though please note that attachments with electronic components will not be submersible.

No. The MLX uses the brush guard, winch, and entire front end of your UTV. However, we will be offering a snow-plow implement that will be compatible with the MLX.

Not yet, but we have loads of ideas and a few awesome attachments currently in R & D that we anticipate rolling out Fall/Winter 2023-24. We currently offer four heavily-tested attachments: the ball mount, pallet forks, cargo carrier, and Garbage Getter. Make sure to follow our socials and subscribe to our newsletter to hear when we release new implements!

We’d love to have you as an authorized MLX dealer! You can apply from the Become a Dealer page. We’ll get back to you after submitting your application to let you know your application status and next steps, as the case may be.

Yes, the Mod Lift X is patented under US Patent No.: 11,400,850 B1.

In true modular fashion, the MLX is designed to fit most UTV brush guards. However, to best serve our customers, we are 3D modeling common UTV brush guards, enabling us to show and tell you that the MLX will fit! Please check out our Compatibility & Fitment page for brush guards we have tested. There is a detailed explanation of proper fitment embedded within the 3D models. We will continuously be updating this list and adding models of a wide range of brush guards. To be certain of fit for brush guards not currently on this list, please submit your brush guard for verification by clicking HERE. If you have any other questions about fit and compatibility, please contact us!

The implements will be attached in different ways. For example, the ball mount and forks drop into the MLX main unit. The cargo carrier is attached on top of the forks, via a clevis pin.

When you get your new Mod Lift X, you'll need to assemble it according to our Assembly, Fitment, & Install Guide. It should take about thirty minutes to assemble your MLX. After that, it's quick and easy! Sixty second install, sixty second uninstall. If you have any questions about the process not answered in the guide, please reach out to us on our Contact page.

The MLX unit hangs onto your vehicle's brush guard and uses your vehicle's front-mounted winch to provide power. After installing the MLX onto your brush guard and hooking it up to your winch according to the Install Guide, you use your winch to raise and lower the MLX.

Purchases made on the MLX website get free shipping to the lower 48 states. If you're in Alaska or Hawaii, please contact us via the form on our Contact page.

You can read and download the Warranty and Return Policy on our Warranty & Returns page.

No, we cannot.

For in-stock items, your order will ship in 2–3 business days.

We ship via FedEx and UPS. You will receive an email notification when your order has shipped. The email will include the FedEx or UPS tracking number for your order as well as a link to the FedEx or UPS website where you can track the shipment.

MLX will process returns within five business days after receiving your return, but it may take up to thirty days for the return to be reflected on your statement from your credit card company.